How To Repair a Broken Hose

Large hose clamps

So you?ve just planted a beautiful garden right in the backyard and you’re ready to nourish those nice plants, vegetables, and fruits with some much needed water, but one major problem is stopping you. You have a broken hose. What a bummer. On the contrary this may be a good time to show off your repairman skills.

Before you get frustrated and throw away the punctured hose, here are the steps to repairing and fixing the hose and have it working as though it was never punctured, just don’t give up on it. These step by step instructions will make sure that you never have to waste a perfectly good hose due to a minor gash or puncture.

Here?s what you need to get started and repair your garden hose:

  • Sharpie or marker
  • Knife
  • Screwdriver
  • A stainless steel clamp

Step 1

Large hose clamps

So you?ve just planted a beautiful garden right in the backyard and you’re ready to nourish those nice plants, vegetables, and fruits with some much needed water, but one major problem is stopping you. You have a broken hose. What a bummer. On the contrary this may be a good time to show off your repairman skills.

Before you get frustrated and throw away the punctured hose, here are the steps to repairing and fixing the hose and have it working as though it was never punctured. These step by step instructions will make sure that you never have to waste a perfectly good hose due to a minor gash or puncture.

Here?s what you need to get started and repair your garden hose:

  • Sharpie or marker
  • Knife
  • Screwdriver
  • A stainless steel clamp

Step 1Use a marker or sharpie to mark the areas that you will be cutting on the hose. Make sure the length is enough that you cut away the area where there is a gash or puncture. Precision in this step is key. You want a clean cut to be able to apply the stainless steel clamp and attach the two sides.

Step 2Use a utility knife, box cutter, or any sharp stainless steel object to cut the hose right on the sharpie draw lines. Like mentioned before be precise. If the cut is too rough it might cause some difficulties when you try to attach the stainless steel hose clamp. Keep this in mind when you cutting the hose and make sure that while cutting out the damaged part it is done in the safest way possible. The best way to do this is to lay the hose down on the ground, apply pressure while holding it, then cutting out the punctured area while following the lines you drew in the previous step. The cuts cannot be slanted and must be real smooth.

Step 3Insert the adjustable hose clamp into each end of the hose. Depending on the thickness of the thin the hose is you may need to adjust the stainless steel clamp appropriately or purchase one that fits in much better. There of course different types of hose clamps depending on your needs. Extra large hose clamps, heavy duty hose clamps, large stainless steel hose clamps are usually reserved for much bigger or thicker hoses. Find the one that the best fit and use it.

Step 4Use your screwdriver to screw on the stainless steel clamp as firm as possible to avoid any leakage when the hose is put to use. The next and final step is to put the newly fixed hose to use and water your garden accordingly. If necessary make any adjustments to the tightness of the clamp.

What Types of Hose Clamps Do You Use Most Often?

Band clamps

Turns out, the problem was one of the large hose clamps that failed.
You came home to a basement floor that was covered in an inch of water. When you were gone the large hose clamps that were holding the tubing to the water heater had broke. In all likelihood just one of the large hose clamps broke first, and the added pressure on the second one caused it to break as well. The result was wet, messy, and required some industrial water damage clean up.
Adjustable Hose Clamps Are Used for a Variety of Purposes
By definition, a hose clamp or clip is a device used to attach and seal industrial hoses onto any kind of fitting like a barb or nipple. Heavy duty hose clamps, stainless steel clamps, and aircraft type hose clamps are, in fact, the tool that mechanics of all levels use as their go to device. Consider some of these uses:

  • Screw hose clamps are often used for temporarily and quickly fixing damaged pipes in emergency situations.
  • Hose clamps can be used as heavy duty zip ties, or as replacements for duct tape.
  • Automotive hoses and household plumbing systems can often be secured with hose clamps.
  • Applying pressure on all sides, hose clamps enable connections without any gaps.
  • Not meant for high pressure situations, hose clamps are typically limited to moderate pressures, like those found in both automotive and home applications.
  • Hoses that get stuck should never be removed by cutting or slitting. These actions can leave a scratch on the barb which will cause a leak.

From washer and dryer hook ups in a home to larger plumbing needs in manufacturing plants, hose clamps often serve a variety of purposes. Although the hose clamp was first invented in 1921 by a former Royal Navy Commander named Lumley Robinson, it remains a tool that is used throughout a number of industries in the year 2017. Few work shops, in fact, would ever exist that did not have a supply of hose clamps available in a variety of sizes and types. From plastic to stainless steel, hose clamps are very much a part of today’s world.